ACR Extreme splitter bracket mounting question

[05Commemorative]

Ok, put on the front splitter today. The two outside brackets though don't seem to mount cleanly to the mount that goes through the grille. wondering if they are not rotated correctly. Can someone post an up close pic of install on each side. (referring to the vertical silver bracket going from splitter to the mount that protrudes through grille. Jut really need the closup of the upper portion. thx

[VENOM V]

Here it is. When installed, the tube deflects the grill and nose upward a bit, but works just fine for me.

https://farm2.staticflickr.com/1713/25931608864_e9a6cbf2cc_b.jpg (https://flic.kr/p/FvugSy)IMG_1402 (https://flic.kr/p/FvugSy) by solomontodd (https://www.flickr.com/photos/20879698@N02/), on Flickr

[ViperJon]

05 Commemorative I have been having the exact same issue. I PM'd both Rapidresults and Venom V for their input. This is one half assed mounting system. In my case I have to use a lot of force to get the bracket on the bolt, it just seems misaligned with the front fascia. The weird design of the base of the mounting bracket makes it want to go on crooked. I just kept stepping back and saying I have to be doing something wrong but doesn't appear so. After I got them tightened on the angle wasn't alighted correctly with the turnbuckle as VenomV's is so I put it away for the night and try again tomorrow.

[ViperJon]

EDIT: Ok, I'm an idiot. The brackets do fit on to the bolt and everything lines up correctly if you are using the CORRECT bracket. The RH bracket is the passenger side and the LH the drivers side ;) ;) ;). They don't actually say that anywhere in the instruction booklet they are just labeled LH and RH.. It is a tight squeeze onto the bolt but it goes. Thanks everybody for the help. All good now.

Just for reference if anyone is researching this in the future the proper torque on the splitter bracket is 48NM or 35.4 Ft pounds.

[05Commemorative]

Thanks guys. For mine, it does not fit smoothly line up like Todds pic shows. I thought I had on the correct sides, but will take off and make sure. They were a pain, so thinking might have done the same thing you did ViperJon.
16858

[ViperJon]

Thanks guys. For mine, it does not fit smoothly line up like Todds pic shows. I thought I had on the correct sides, but will take off and make sure. They were a pain, so thinking might have done the same thing you did ViperJon.
16858

You did, mine looked just like that lol...live and learn. When put on correctly it lines up with the exact angle like Todds.
Easy fix.

http://i.imgur.com/mmwBZVE.jpg?1

[05Commemorative]

must be the fault of the color of the car... seriously, thank you very much. I know what I am doing tonight.

You did, mine looked just like that lol...live and learn. When put on correctly it lines up with the exact angle like Todds.
Easy fix.

http://i.imgur.com/mmwBZVE.jpg?1

[ek1]

I dont mean to hijack this thread, but a quick question - are all the tools needed to install the front splitter extension and the rear diffuser strakes included with the car?

[ViperJon]

I dont mean to hijack this thread, but a quick question - are all the tools needed to install the front splitter extension and the rear diffuser strakes included with the car?

To actually install it...no.

Required tools: 10mm ratcheting end wrench, 3/8”
drive, 6” extension, 15mm socket, 10mm deep socket,
4mm hex key, 11mm wrench, and a torque wrench.

[05Commemorative]

fixed it. Thanks for the help and why this forum is so valuable.

[SharpMan]

I'm thinking of getting the hardware all anodized black.

[docwviper]

To actually install it...no.

Required tools: 10mm ratcheting end wrench, 3/8”
drive, 6” extension, 15mm socket, 10mm deep socket,
4mm hex key, 11mm wrench, and a torque wrench.

A very very valuable post. Thanks guys. Great info. Excited to put my stuff on in a few weeks. Just gotta find the time now.

[A C R]

I installed the front spiller brackets and it sure put a lot of pleasure on the grill especially on the left side and yes I did put them on the correct side. hope it doesn't crack the grill.

[SSGNRDZ_28]

It is a tight fit for sure. I'm going to offer them in anodized aluminum and have lowered the OD of the tube slightly which helps ease contact with the grille and also the overall flange size which helps when inserting them. 23416

[LATAMUD]

It is a tight fit for sure. I'm going to offer them in anodized aluminum and have lowered the OD of the tube slightly which helps ease contact with the grille and also the overall flange size which helps when inserting them. 23416
Willing to sell just the two frame brackets?

[SSGNRDZ_28]

Willing to sell just the two frame brackets?

Yes they will be for sale individually once available. There will also be a tow hook add-on option. Most likely the end of March.

[LATAMUD]

Yes they will be for sale individually once available. There will also be a tow hook add-on option. Most likely the end of March.

Awesome. Will be watching out for them.

[Purple Haze]

Does this lower the front clearance to the ground or just extend it forward? When I pick up my new ACR they said it will not be mounted on the car so I'll have to do it later...Unless I can talk them into it? I assume the bottom portion bolts to the front bumper or such below? Sorry I'm a newbie...

[SSGNRDZ_28]

Does this lower the front clearance to the ground or just extend it forward? When I pick up my new ACR they said it will not be mounted on the car so I'll have to do it later...Unless I can talk them into it? I assume the bottom portion bolts to the front bumper or such below? Sorry I'm a newbie...

It just extends it forward. It is not hard to do,
14 bolts for the splitter plus the brackets and strakes shown. You might get a ratcheting low profile wrench to make it easier as there is little clearance to the fascia. This is mentioned above.

[BlueAdder]

Ok, put on the front splitter today. The two outside brackets though don't seem to mount cleanly to the mount that goes through the grille. wondering if they are not rotated correctly. Can someone post an up close pic of install on each side. (referring to the vertical silver bracket going from splitter to the mount that protrudes through grille. Jut really need the closup of the upper portion. thx

Darn you for making have doutbs :D now I have to look at my own install tonight and look a the angle of the brackets.

[ansman]

Question. Where can you get an extra splitter?

[SSGNRDZ_28]

Question. Where can you get an extra splitter?

I sell reproductions of the OEM the extensions. I will soon have all of the parts in stock other than the carbon splitter itself (bolts brackets strakes extensions)

[38D]

It is a tight fit for sure. I'm going to offer them in anodized aluminum and have lowered the OD of the tube slightly which helps ease contact with the grille and also the overall flange size which helps when inserting them. 23416

Awesome mod. I'll be in for a set for sure.

[Purple Haze]

Thank you sir!!!


It just extends it forward. It is not hard to do,
14 bolts for the splitter plus the brackets and strakes shown. You might get a ratcheting low profile wrench to make it easier as there is little clearance to the fascia. This is mentioned above.

[venom700]

It just extends it forward. It is not hard to do,
14 bolts for the splitter plus the brackets and strakes shown. You might get a ratcheting low profile wrench to make it easier as there is little clearance to the fascia. This is mentioned above.

have you prepared it yet bro? I think ill be needing that as long as the kit gonna be ready foon

[SNKEBIT]

How much for the frame brackets?

[SSGNRDZ_28]

have you prepared it yet bro? I think ill be needing that as long as the kit gonna be ready foon


How much for the frame brackets?

Yes these are done, ready to ship, available for purchase on my website.

26409

[venom700]

Yes these are done, ready to ship, available for purchase on my website.

26409

I saw it Doug bro, but sorry I couldn't even understand which part I should choose exactly to order, if you could support with the link. One more question, the ACR wing bracket stand that fits on the trunk, do you have it too???


26417

[bluesrt]

I too want these better front splitter supports but don't get how to order

[SSGNRDZ_28]

Stainless adjustable stakes: DSE-VP-EA-004: ACR Extreme Splitter Adjustable Support (Set of 2)

Splitter brackets (anodized aluminum)
DSE-VP-EA-007: ACR Extreme Splitter Support Bracket (Set of 2)

[bluesrt]

Can we use our factory stainless stakes with your improved brackets?

[SSGNRDZ_28]

Can we use our factory stainless stakes with your improved brackets?

Yes everything is compatible and interchangeable with OEM.

[Mihai]

what is the part number of the OEM brackets and OEM support rods ?

[Mihai]

what is the part number of the OEM brackets and OEM support rods ?

help :) !

[SSGNRDZ_28]

Here are the OEM part numbers:

My equivalents cost a fraction of these, the brackets won’t corrode, and are lighter. All are in stock ready to ship.

Thanks,
Doug

Front Splitter Spoiler=Extreme Front Splitter. STRUT. Front Splitter. [MXE] OR [MET]. . Required: 001
68322463AA
$555.00


Front Splitter Spoiler=Extreme Front Splitter. STRUT HARDWARE KIT. Front Splitter. Attaching Parts. [MXE] OR [MET], One Kit Includes Right & Left. . Required: 001
68322461AA
$77.00

BRACKET. Front Splitter. Left. Front Splitter Spoiler=Extreme Front Splitter. . Required: 001
68322465AA
$1850.00


BRACKET. Front Splitter. Right. Front Splitter Spoiler=Extreme Front Splitter. . Required: 001
68322464AA
$1850.00