does anyone sell this part minus exhaust ??

[vegasgtr]

ordered the Corsa's and love this titanium "mid pipe" if you will.. Ill call agency on monday and see if they only sell that part.

does anyone else make that part alone?

[vegasgtr]

no one sells the mid section?

[Viktimize]

That looks like it replaces the cats. I'm still waiting on JonB to give some kind of reply about the hi flos he has says are in production.

[vegasgtr]

That looks like it replaces the cats. I'm still waiting on JonB to give some kind of reply about the hi flos he has says are in production.

Its Agency's Titanium exhaust. The one in the pic is with the high flow cat.They also make it without the cat. I think with 1 high flow cat it will free up some good power.

http://www.agency-power.com/catalog/...150771811.html

[DZnutz]

Why havent you called the manufacturer yet?

[vegasgtr]

Why havent you called the manufacturer yet?

Yesterday was Sat and today is sun.. they are not open.

[G37Sam]

Subscribing!

Why not just get it custom made since it's a bent straight pipe?

[Viktimize]

Subscribing!

Why not just get it custom made since it's a bent straight pipe?

This is what I am wondering about. We have a good exhaust shop here in town. I might ask them to just make me a mid pipe with a high flow cat wleded in. it is just a flange and pipe with one bend, shouldn't be too hard. But if I could grab ne of the artsRack sets I know for sure the angles will be pefect to ensure no rubbing or anything on the inside of the rocker.

[mjorgensen]

That AP kit looks like the front hanger for the exhaust is retained, without a flexing joint I would think the hard pipe would be eventually damaged, the engine mounts are very soft and allow lots of movement that is why headers and exhaust eliminate the front hanger. Not sure if the cats Jon is making up will have a flex joint or remove the front hanger.

[Ninjakris]

Mark has a good point. When I had my Gen III, there were two high flow options. Random Technology didn't have a flex or a front hanger IIRC. The other brand (can't seem to remember the name) did have a front hanger and flex joint. From my personal experience with the random technology high flow's, it was just fine without the flex and front hanger.

[Steve M]

That AP kit looks like the front hanger for the exhaust is retained, without a flexing joint I would think the hard pipe would be eventually damaged, the engine mounts are very soft and allow lots of movement that is why headers and exhaust eliminate the front hanger. Not sure if the cats Jon is making up will have a flex joint or remove the front hanger.

Based on what I saw, he was eliminating the flex joint and removing the front hanger.

[JonB ~ PartsRack]

The flex mesh is a restriction, causes turbulance inside, adds weight and cost. NOT NEEDED The 3" pipe moves about .75" at WOT at the hanger-less elbow, and the OE mounts easily allow that. [as proven by every Belanger Viper header install in 20+ years.]

If you order G5 bolt-in HF cats they ship in 10 days or so.

[Viktimize]

The flex mesh is a restriction, causes turbulance inside, adds weight and cost. NOT NEEDED The 3" pipe moves about .75" at WOT at the hanger-less elbow, and the OE mounts easily allow that. [as proven by every Belanger Viper header install in 20+ years.]

If you order G5 bolt-in HF cats they ship in 10 days or so.

Right on. How much are they? Haven't seen an update in quite awhile as to whether these were ready or not.

[vegasgtr]

called Agency power.. no luck. they wont sell it separate.

JonB has the pipes with highflown cats? anyone can confirm?

[vegasgtr]

I think this is it!!

will be ordering from Jon if this is indeed for Gen V !!
http://www.viperpartsrack.com/viper-...converters-srt

maybe Jon can chime in.. can these be installed from underneath without removing the side skirts? i just installed my crosa Yesterday , I wish he would have announced that it was done....

[viper04]

I think this is it!!

will be ordering from Jon if this is indeed for Gen V !!
http://www.viperpartsrack.com/viper-...converters-srt

maybe Jon can chime in.. can these be installed from underneath without removing the side skirts? i just installed my crosa Yesterday , I wish he would have announced that it was done....

No, they can not be installed from underneath without removing the side skirts, it will have to be removed. In your case again. It's not that hard to do.

[JonB ~ PartsRack]

What He Said. (thanks)