Results 1 to 20 of 20
  1. #1
    Enthusiast
    Join Date
    Oct 2013
    Location
    Viper Drive, AZ
    Posts
    793

    Front Fascia Removal - GEN II

    Removing the Front Fascia from a GEN II

    Parts:





    Tools:




    Tape off the areas of the front fascia that will be susceptible to scratching…

    • the areas around the outer ends of the fascia and inside the wheel wells from the headlight to the very bottom



    • the areas in the crosshairs just below the 4 fascia panel retainers
    • the areas in the crosshairs surrounding the 4 fascia panel retainers



    Put a protective pad/blanket down on the floor just below the front fascia so that when you are pulling it off the viper, it can be set down to unplug the wiring harnesses.

    Remove all of the front fascia fasteners (5 hex screws at each wheel well opening, 4 fascia panel retainers inside the crosshairs, 11 hex bolts under the fascia and 7 fascia panel retainers on top of the fascia) before attempting to remove the fascia. Be looking for shims to fall out of the fascia/wheel well area. I didn’t have any, but I’ve heard that they may be there. I did have a stack of 3 shims on the middle fascia panel retainer on the top of the fascia.



    I also had a very unusual looking shim on the driver side fascia panel retainer located just below the headlamp.



    Don’t worry about mangling or breaking the fascia panel retainers. They are designed as a single-use product. They should be replaced with new ones (Chrysler # 6501067, fascia panel retainers).

    Remove the 5 hex screws at each wheel well opening using a 5/16” socket or wrench
    If this is the first time that you’re removing the front fascia, I would recommend that you add more painters tape over the entire area where these screws were removed before you actually start removing the fascia.



    There will be binding in the area between the fascia and the wheel well once you start pulling the end of the fascia out away from/around the wheel well (which comes later). The ends of the fascia can be scratched by the outside end of the wheel wells.

    Remove the 4 fascia panel retainers located inside the crosshairs using the panel clip pliers.





    Be very careful not to scratch the paint around and below the retainers as they will not come out easily.

    Remove the 11 hex bolts located under the front fascia just behind the bottom chin spoiler using a 7/16” socket (a small drive socket extension is very handy here). There are small fascia outboard close out panels at each end of the fascia that can be easily removed once the 2 closest to the outside hex bolts have been removed from each end of the fascia.



    Open the hood (it does not need to be removed).
    Remove the 7 fascia panel retainers located on the top of the fascia just inside the hood using the panel clip pliers.

    • The 3 in the very middle are the easiest. Leave the center one in place until all others have been removed so that the fascia will remain in place until final removal.
    • The next one out on the passenger side may require that you loosen the Hood Ajar Switch located near the passenger side hood latch and headlamp. Pull up while rocking the switch out of the switch mounting bracket.
    • The next one out on the driver side may require that you remove the Hood Slam Bumper located near the driver side hood latch and headlamp. Mark the threads of the slam bumper to determine the replacement height. Rotate the slam bumper counterclockwise and remove it from the hood latch.
    • The 2 outermost fascia panel retainers are a BIATCH to remove. There is one located just below each headlamp. This is a picture of the outermost driver side retainer.



    • The outermost retainers can be accessed by pulling the end of the fascia away from the wheel well.



    • The panel clip pliers can be maneuvered into the opening. You have to balance how much you feel comfortable pulling on the fascia (as it will be binding) with how much space you need to get the retainer removed. You only need to get the head of the retainer removed/broken off. The fascia can be lifted over any remaining retainer stump. You can use any tool of your choosing to get these out. A sharp tool may be used to cut the tops off the retainers.



    Pull the outermost ends of the fascia away from the wheel wells (if you haven’t already done this). Let the ends of the fascia sit against the outside edge of the wheel well (hopefully this area has been taped off for protection against scratching). The fascia can be pulled away from the reinforcement bar. You may have to pull up and then out if you weren’t successful in fully removing those two outermost fascia panel retainers. Set it down on the protective pad/blanket.

    Disconnect the side marker lamp and fog lamp wiring harnesses. You may want to mark each harness so that they don’t get crossed during the installation (although this can be checked/tested by turning on the lights during the installation process). Disconnecting these harnesses can be completed at the very beginning by accessing the wiring harnesses through the wheel well rubber plugs (4” in diameter) located on the front most side of each front wheel well.



    There will probably be some debris that falls out and is caught in and around all of the close out panels.

  2. #2
    Greatest how-to ever

  3. #3
    Enthusiast
    Join Date
    Oct 2013
    Location
    South of London, Surrey
    Posts
    7,577
    Just love your How to Guides, 5 Stars Ken

  4. #4
    Enthusiast
    Join Date
    Jan 2014
    Location
    Southwest FL
    Posts
    665
    Like others I really love your detailed how to posts. I really want to get the hood gap problem fixed on my 2002. Where is the best place to get shims if I need them?

  5. #5
    I second this. Is there anywhere to buy shims today?

  6. #6
    Quote Originally Posted by GhostStalker27 View Post
    Greatest how-to ever
    Or close, nice how to!

  7. #7
    Enthusiast
    Join Date
    Apr 2014
    Location
    Texas
    Posts
    197
    great how-to. im having my brother install hid lights/fogs on the car and this will help a lot! thanks

  8. #8
    Enthusiast
    Join Date
    Apr 2015
    Location
    Valley of the Sun
    Posts
    736
    Quote Originally Posted by TitleMine View Post
    I second this. Is there anywhere to buy shims today?
    Found this great old thread about Gen II fascia removal (a very belated thanks, Ken!)

    I didn't see any follow up responses regarding the availability of shims. My front hood/fascia area has some gaps and alignment issues, so will probably give this DIY a go sometime soon. Are these shims available anywhere?

    Thanks, Drew

  9. #9
    Enthusiast
    Join Date
    Oct 2013
    Location
    Tampa / Kuwait
    Posts
    836
    Quote Originally Posted by drewsss View Post
    Found this great old thread about Gen II fascia removal (a very belated thanks, Ken!)

    I didn't see any follow up responses regarding the availability of shims. My front hood/fascia area has some gaps and alignment issues, so will probably give this DIY a go sometime soon. Are these shims available anywhere?

    Thanks, Drew
    Don't know about the fascia shims but I looked up the ones for the hinge covers a few weeks ago at around $5 each. SS washers are around $0.14 each. If you need the open sided shim to work around tight areas you can always cut a slit into a washer with a grinder as a cheaper alternative.

  10. #10
    Enthusiast
    Join Date
    Oct 2013
    Location
    Viper Drive, AZ
    Posts
    793
    Quote Originally Posted by drewsss View Post
    Found this great old thread about Gen II fascia removal (a very belated thanks, Ken!)

    I didn't see any follow up responses regarding the availability of shims. My front hood/fascia area has some gaps and alignment issues, so will probably give this DIY a go sometime soon. Are these shims available anywhere?

    Thanks, Drew
    I don't know where to get any shims. Getting the front fascia off is a step in the hood realignment process. There have been multiple threads across the viper forums on alignment with varying degrees of success. Good luck.

  11. #11
    Enthusiast
    Join Date
    Apr 2015
    Location
    Valley of the Sun
    Posts
    736
    Thanks, guys. What's a reasonable amount of time to set aside for fascia removal? Is this an all-day event, or can I possibly do it in a few hours?

    I know that we used to have DIY sessions when Eddie worked over at Bill Luke Dodge. May bounce off the idea of having a "fascia removal" class sometime soon for club members.

  12. #12
    Enthusiast
    Join Date
    Oct 2013
    Location
    Viper Drive, AZ
    Posts
    793
    Now that I've done it a few times, it only takes me less than an hour.

  13. #13
    Enthusiast
    Join Date
    Apr 2015
    Location
    Valley of the Sun
    Posts
    736
    Thanks, Ken. I will attempt it myself, and if unsuccessful, you may see a frustrated Viper owner in your driveway, equipped with multiple six-packs whilst whimpering for help.

  14. #14
    Enthusiast
    Join Date
    Oct 2013
    Location
    Viper Drive, AZ
    Posts
    793
    I'm more than willing to help. Just let me know the time and place. I'm in a rental house right now and my tools are mostly packed away though.

  15. #15
    Enthusiast
    Join Date
    Apr 2015
    Location
    Valley of the Sun
    Posts
    736
    Hi Ken - sounds great. Just sent you a PM.

    Thanks.

  16. #16
    Enthusiast
    Join Date
    Oct 2013
    Location
    Just visting this planet.
    Posts
    119
    I found it much easier to leave the fascia attached to the fiberglass bumper and remove it as an assembly. Less shims to deal with and don't have to fool with the plastic retainers.

  17. #17
    Enthusiast
    Join Date
    Apr 2015
    Location
    Valley of the Sun
    Posts
    736
    Quote Originally Posted by Mad Max View Post
    I found it much easier to leave the fascia attached to the fiberglass bumper and remove it as an assembly. Less shims to deal with and don't have to fool with the plastic retainers.
    Thanks for the info!

  18. #18
    Enthusiast
    Join Date
    Oct 2014
    Location
    CANADA
    Posts
    389
    Great DIY again...the best for noobie like me.

    Thanks

    Ben
    1997, winterized Red R/T 10

  19. #19
    Enthusiast
    Join Date
    Oct 2013
    Location
    Viper Drive, AZ
    Posts
    793
    Quote Originally Posted by Mad Max View Post
    I found it much easier to leave the fascia attached to the fiberglass bumper and remove it as an assembly. Less shims to deal with and don't have to fool with the plastic retainers.
    I don't completely understand. Can you elaborate on which shims wouldn't come into play and maybe some pictures.

  20. #20
    Enthusiast
    Join Date
    Oct 2013
    Location
    Just visting this planet.
    Posts
    119
    There are shims shown in your pictures that are between the fascia and the fiberglass bumper. By leaving all of the plastic push fasteners in place and unbolting the bumper from the front frame mounts the fascia can be removed with the bumper still attached and therefore the shims that are in between the fascia and bumper are not disturbed and cannot fall out.


 

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •